Archive for the ‘do-it-yourself home improvements’ Category
Refinishing Basements Is Really A Win-Win Home Improvement Project!
Many individuals decide to buy their houses soon after they get married. They buy them thinking that they are a lot more spacious than anything they’ll ever need. Even so, over the years, things change. The couple adds more possessions, babies are born, and the house just appears to be straining at the seams to encompass it all. This is the time the dilemma will start. Should we purchase a new house, though we love the one we’re in, or should we find an alternative solution? As people start thinking about expansion, refinishing basements gets to be a key thing to consider. In fact, this method won’t necessitate moving, but it’ll make use of extra space in the house you already own.
Refinishing basements expands living space
Infants do not require a lot of space. They can crawl around in a couple of rooms and be perfectly content. When they start maturing, though, their play gets to be more active, and they need room to run around and let off steam. During the summer time it’s easy just to send them outside. During the cold months, though, when they are a lot more confined to your house, you need space to be able to have fun. Nothing could possibly be much more ideal than having a few basement refinishing ideas and turning your own cellar into an entertainment area which can be used by the whole family. Performing a basement remodel will be a far less expensive method of getting the needed space without needing to pay moving costs or perhaps build an add-on onto your house.
Even if you do not have young children, your personal interests are going to develop over time, plus your friendship base will grow so much that you will want to entertain more than just one or two folks. Creating an entertainment area in your basement is yet another good reason for doing a bit of remodeling. Maybe you’ll want to put in a bar, a conversation area, a pool table, along with the other accessories which make for excellent entertaining.
Refinishing basements add personal benefit for the current homeowner as well as additional resale value
When all is said and done, you simply can’t lose by refinishing your basement. You will get the added living area for all the years that you live in your house, and refinishing basements can add as much as 30% to the resale value, by increasing living space, should you decide to sell in later years.
Crown Molding Coping Cuts
When putting in crown molding, a coped joint is preferable to a miter in a number of ways. Wooden expands and contracts and on account of this movement miters tend to open on the quick point or the lengthy point. A coped corner stays tight as each piece expands and contracts. A coped joint additionally suits well when installed in a room with minor imperfections, equivalent to partitions which or not sq. or ceilings and partitions that are less than straight, level, and plumb. A coped joint is also extra adjustable. If there is a hole within the joint, you need solely to pry the other end of the trim to squeeze the joint tight. A coped joint can also be simple to work with. For instance is a chunk of trim is reduce a bit short, by 1/eight inch let’s imagine, the hole is covered by the subsequent piece of coped trim. Miters by contrast reveal any errors. Here are step by step instruction to coping your crown:
Step 1-Miter the inventory-Make a marking jig. Label the top of an oblong scrap of half inch plywood as ceiling and its right side as wall. Measure the moldings ceiling projection and its drop down the wall by nesting it in a framing square. Transfer these measurements to the piece of plywood, and cut between the factors, eradicating the jigs corner. This jig might be used to ensure correct crown positioning throughout the cope and the install.
Step 2-Create a stop that replicates the ceiling position. The distance between the stop and the miter noticed’s fence ought to match the ceiling projection. Examine the cease location with the marking jig.
Step 3-Reduce a 45 degree miter and measure for length. Place the top edge of the molding down in opposition to the stop, and put the underside fringe of the crown towards the saws fence. If coping to the left, the long point of the miter shall be at the backside edge of the crown molding. Make the miter. Then utilizing a measurement taken between the corners of the wall, measure from the lengthy point of the miter to the mark the trims length.
Step four-Cope the reduce-An auxiliary fence helps to secure the trim for the cope. With the ceiling-aspect edge of the trim flat towards the fence and the wall aspect edge flat against the stand, snug up a cease to maintain it in position. Use the marking jig to ensure that the trim is seated correctly.
Step 5-A jigsaw fitted with a coping foot or conventional coping saw can be used at this point. Make several relief cuts earlier than following the profile of the molding. Hold the noticed considerably less than vertical to provide the cope a slight back cut.
Stop 6-Check the Match-Use a scrap of the molding to test the accuracy of the cope. Whether the nook is less than or higher than ninety degrees the coped joint stays tight. If the joint isnt as tight as you want, fine tune the cope with a rasp of a sanding sponge.
Step 7-Install the crown molding-Reduce the trim to length with a ninety degree cut. This butt end is covered by the adjacent coped piece of trim. Lower pieces of trim greater than 8 ft. This helps to maintain the corners tight over time. When installing the trim, do not nail inside 2 ft of every end till the joint suits the way you need it.
At Installingcrownmolding.org you will learn about how to cope crown molding , crown molding coping jig and coping crown molding angles.
Faux Granite Countertops: Cheaper Compared With Natural Stone
Do you find the cost of granite countertops prohibitive?
Faux granite countertops may be your solution to affordable granite decor.
Fabrication technological innovation has moved the price of granite countertops down noticeably over the most recent few years, but it even now is simply not within reach of many individuals, and, despite the fact that granite is actually fast evolving into the material of choice, to afford the look many are finding a faux granite countertop may realize a very similar appearance without the equivalent outlay of money.
There are actually many items on the market today which can switch your aged, dull laminated counter tops into what appears to be granite without having nearly the expense, or time of adding a new natural stone counter top. A faux granite countertop may be sprayed on and available to make use of within a working day or two, dependent on drying conditions, and normally for under $25.
Krylon produces an aerosol paint called Make It Stone Textured Paint, obtainable for around $10 a can and is accessible in almost all home improvement outlets as well as big cut price stores. With any kind of expertise at all in using spray paint, it is a pretty easy do-it-yourself project. Still keep in mind, this is a spray paint and it is going to drift and get on things you do not really want to look like a faux granite counter top.
Planning is Key for the Very best Finished Project
To get ready for your assignment, eliminate anything from the room you do not want even the smallest bit of paint to cover. After that softly sand the laminated countertop. This isn’t to get rid of the finish, but it’ll need to be a bit rough prior to painting.
Tape all the parts you do not want to look like a faux granite countertop, beginning with the straight edges first. That would involve wall surfaces next to the top. Then utilizing paper or plastic-type drop cloths, tape it to larger sections of the wall space and flooring. Wash the surface area to get painted with a moist cloth to get rid of all of the dust particles.
Make use of a greyish primer on the surface to be painted, spraying it evenly. The use of a paint primer will help the faux granite counter top fresh paint adhere to the surface area and reduce running. Apply evenly and let dry completely, and then once it’s dry you are able to commence spraying on your faux granite counter top. Positioning the can eight to twelve inches away from the area use a mist method beginning at one end and then working toward the other. This process ought to be repeated until at least three coats have been properly applied.
As soon as dry, or after about 30 minutes, apply a spray on clear coat sealer. A number of coats are advised so that you can enable the faux granite countertop to be cleaned as normal.
